Jump to content
  • entries
  • comments
  • views

Physics of Running



Energy Transfer during Running

When a person runs, their body must convert potential energy into kinetic energy. Potential energy is the energy stored within a system. Potential energy is used when the system uses kinetic energy to move in a horizontal direction.

In the human body, potential energy is stored in the form of chemical energy. The chemical energy comes from the food that a person consumes throughout the day. The body needs a certain amount of calories (the energy from food) in order to perform certain activities. If the runner has not consumed enough calories throughout their day, they will run out of potential energy and become tired. This is because the body is not very efficient at retaining energy. Energy cannot be created or destroyed, but it can go elsewhere. As the person runs, most of their stored energy is released in the form of thermal energy. This is why people get hot and start to sweat when they do physical activity such as running. The body is heating up because it is literally burning the calories that it has consumed in order to keep moving in a horizontal direction. The runner will sweat, because sweating is the body's natural cooling mechanism. If the runner did not have the ability to sweat, the conversion of potential energy (the chemical energy) into kinetic energy which is released as thermal energy would cause the runner's body to overheat. The chemical energy that the runner consumes in the form of calories is also released in the form of sound energy. Every time the runner's foot hits the ground, energy is leaving the runner's body as sound waves emit from the impact of the runner's foot on the ground. Because energy is being released from the runner's body with every step they take, it is important for the runner to consume enough chemical energy in the form of calories prior to their run. The runner's body needs a substantial amount of calories as a reserve so that they will have more to burn as their potential energy is released throughout the run.

Thermal energy is measured in calories. Calories are released from a given item as it burns. The amount of calories that are in something depends directly on the amount of chemical bonds that are broken and formed as it burns. For example, when a piece of wood burns, 3000 calories of thermal energy are released per gram. When an apple is burned however, it releases about 600 calories of thermal energy. Therefore, it is reasonable to assume that there is more energy available from breaking the atomic bonds in wood than from breaking the atomic bonds in an apple.

One calorie is defined as the amount of thermal energy needed to raise the temperature of one gram of water one degree Celsius. Calories burn very slowly in the human body, and as they do, kinetic energy becomes available to the runner. 1 calorie is the equivalent to 4.186 Joules of energy. So, the more calories that the runner consumes prior to running, the more energy they will have available to them throughout the run. The runner�s energy can also be measured in the form of watts, or electrical power. One calorie also translates to about 4.186 watts. So, if the runner has 500 calories available to them, they are capable of producing over 2000 watts of electrical power.

When the body uses the calories it has consumed, it is not very efficient at conserving this energy. As the leg muscles contract to propel the runner forward, about 75% of the chemical energy that the runner has consumed is lost due to the heat (thermal energy) that the body gives off as it converts it stores (potential) chemical energy into kinetic energy.

Kinetic energy is equal to one half of the runner's mass times their velocity squared (KE=1/2mv^2). So, if the runner has a mass of 60 kg and wants to run at a rate of 9m/s, they will use about 2,430 Joules of energy. The runner is not able to change their mass, but they can increase or decrease their use of kinetic energy by increasing or decreasing their velocity. If the runner has not consumed a lot of chemical energy throughout their day, it would be wise for them to decrease their velocity as to decrease their kinetic energy and therefore use less of their stored potential energy.

The power that the runner generates during their run depends on the amount of time it takes them to complete the run. If they decide to run a given distance, their power output will depend on how long it takes the runner to complete the given distance. The power of the runner can be calculated by dividing the amount of work that they do during the run by the amount of time it takes them to complete the run. (P=W/t). If the runner completes the run in a short amount of time, they will have a relatively large power output. If it takes them a long time to complete their run, the runner will not generate as much power. The amount of time that it takes the runner to complete the run depends on their velocity. An increased velocity will allow the runner to complete a given distance in less time. This will increase their power output, because they are doing the same amount of work as they would be doing if they ran the distance at a slower pace, but they will be completing the run in less time. Completing the run in less time requires the runner to expend more of their stored potential energy. So, when the runner decides to increase their velocity, they will increase their kinetic energy. They will also decrease the amount of time it takes them to complete the run, and therefore increase their power output. Because it requires more energy to produce a higher power output, the runner will need to consume more chemical energy (calories) in order to run at a higher velocity.


Recommended Comments

There are no comments to display.

Add a comment...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Create New...